Toyota Land Cruiser 100/Amazon, Lexus LX 470

since 1997 release

Repair and operation of the car



Toyota Land Cruiser, Amazon, LX470 Lexus
+ Identification numbers of the car
+ Governing bodies and methods of safe operation of the car
+ Settings and routine maintenance of the car
+ Engine
+ Cooling systems of the engine, heating of salon and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Electric equipment of the engine
+ Control systems of the engine and decrease in toxicity of the fulfilled gases
+ gear shifting Box
- Transmission line
   Specifications
   Driveshafts and hinges - the general information
   Check of a condition of the transmission line
   Removal and installation of the driveshaft
   Replacement of cardan hinges
   Driving shaft / half shafts, - the general information and check of a state
   Removal and installation of half shafts, bearings and epiploons of the back bridge
   Replacement of an epiploon of the leading gear wheel of differential
   Removal and installation of assembly of the back bridge
   Removal and installation of power shafts
   Replacement of protective covers and service of CV JOINTS
   Removal and installation of assembly of forward differential
   Removal and installation of naves with the switched-off drive
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


99e20293




Replacement of an epiploon of the leading gear wheel of differential

Extraction of epiploons of the leading gear wheels back and forward (models 4WD) of differentials is made in an identical manner.


 PERFORMANCE ORDER

1. Weaken nuts of fastening of back wheels. A car back also establish to Poddomkratta it on props. Prop up forward wheels antiretractable boots. Remove wheels, it is necessary for more exact measurement of a pretightness of the leading gear wheel.
2. Disconnect the driveshaft from differential (see the Section Removal and installation of the driveshaft), shift it aside and tie up a wire to frame elements.
3. By means of a dinamometrichesky key measure a torque of rotation (pretightness) of the leading gear wheel (address to an accompanying illustration). Write down result of measurement.
4. By means of a chertilka or a center punch mark the provision from each other of an axis of a gear wheel, a fixing nut and a connecting flange.
5. Count quantity of open rounds of a carving from a face surface of a nut to a gear wheel axis cut, write down result.
6. Record a flange from a provorachivaniye by means of the special adaptation, or having passed a big screw-driver throughout an opening of fastening of a collar of the cardan hinge and having jammed it under the arm located behind, a case stiffening rib, or tubular section of the bridge (address to an accompanying illustration) and release a nut of the leading gear wheel.
7. Thaw a gear wheel nut.
8. Remove a connecting flange, in case of need use a stripper (address to an accompanying illustration).

Do not try to hook a flange the lever at all, or to bring down him a hammer!

9. Take an old epiploon from the landing nest (address to an accompanying illustration).
10. Grease sponges of a new epiploon with high-temperature greasing and evenly begin to knock it in the landing nest. Track perpendicularity of landing of an epiploon, as a mandrel it is possible to use a face head of the suitable size, or a piece of a pipe of the corresponding diameter (address to an accompanying illustration).
11. Having achieved combination of the components of landing tags put in the course of dismantle, establish into place a connecting flange, – in case of need tighten a flange a nut, but not its zastukivayta into place a hammer at all.
12. Grease with not stiffening sealant vents in the center of a flange.
13. Establish a washer (if it is provided) and carefully tighten a nut so that the axis of a gear wheel acted over its face surface on the quantity of rounds of a carving noticed earlier (see paragraph 5).
14. Measure a torque of rotation of a gear wheel, then tighten a nut for compensation of the changes connected with installation of a new epiploon a little more, the torque has to be a little (but no more than on 0.6 Nanometers) more than at an old epiploon.
15. Connect the driveshaft, establish to the place of a wheel, lower the car on the earth and tighten wheel nuts with the demanded effort (see the Head Nastroyki and routine maintenance of the car).