|
Toyota Land Cruiser 100/Amazon, Lexus LX 470since 1997 releaseRepair and operation of the car |
|
Toyota Land Cruiser, Amazon, LX470 Lexus + Identification numbers of the car + Governing bodies and methods of safe operation of the car + Settings and routine maintenance of the car + Engine + Cooling systems of the engine, heating of salon and air conditioning + the Power supply system and production of the fulfilled gases + Electric equipment of the engine - Control systems of the engine and decrease in toxicity of the fulfilled gases Specifications System of onboard diagnostics (OBD) - the principle of functioning and codes of malfunctions Application of an oscillograph for supervision of working signals of a control system Check of a state and replacement of ESM Information sensors - the general information and check of serviceability of functioning Replacement of information sensors System of catching of fuel evaporations (EVAP) - the general information, check of a state and replacement of components System of the operated ventilation of a case (PCV) The catalytic converter - the general information, check of a state and replacement + gear shifting Box + Transmission line + Brake system + Suspension bracket and steering + Body + Onboard electric equipment |
Application of an oscillograph for supervision of working signals of a control system General information Digital multimeters perfectly are suitable for check of the electric chains which are in a static state, and also for fixing of slow changes of the traced parameters. When carrying out the dynamic checks which are carried out on the working engine and also at identification of the reasons of sporadic failures the oscillograph becomes absolutely irreplaceable tool. Some oscillographs allow to keep oscillograms in the built-in module of memory with the subsequent conclusion of results to the press or their transfer to the carrier of the personal computer already in stationary conditions. The oscillograph allows to observe periodic signals and to measure tension, frequency, width (duration) of rectangular impulses, and also levels of slowly changing tension. The oscillograph can be used when performing the following procedures:
Reliability and simplicity of operation of modern oscillographs do not demand any special special knowledge and experience from the operator. Interpretation of the received information can be easily made by elementary visual comparison of the oscillograms removed during check with the temporary dependences typical for various sensors and actuation mechanisms of automobile control systems given below. Parameters of periodic signals General information Usually characteristics of the faulty device strongly differ from reference that allows the skilled operator easily and quickly to reveal the refused component by the analysis of the corresponding oscillogram. Signals of a direct current The only performance data of such signals is tension. Signals of a direct current are developed by the devices given on illustrations below: Sensor of temperature of cooling liquid of the engine (ECT)
The sensor of temperature of the soaked-up air (IAT)
Sensor of provision of a butterfly valve (TPS)
Warmed up a lambda probe
Measuring instrument of a volume expense of a stream of air (VAF)
Measuring instrument of mass of air (MAF)
Signals of alternating current The main characteristics of these signals are amplitude, frequency and a form of a signal (address to illustrations below).Sensor of a detonation (KS)
Inductive sensor of turns of the engine
Frequency-modulated signals (WC) Performance data of frequency-modulated signals are amplitude, frequency, a form of a signal and width of periodic impulses. Sources of a WC of signals are the devices given on illustrations below:
Inductive sensor of provision of a camshaft (CMP)
Inductive sensor of speed of the movement of the car (VSS)
The sensors of turns and the provision of shaft working at effect of the Hall
Optical sensors of turns and provision of shaft
Digital sensors of thermometric measurement of mass of air (MAF) and absolute pressure in the inlet pipeline (MAP)
The signals modulated on width of an impulse (ShIM) Performance data of signals of the pulse-width modulation (PWM) are amplitude, frequency, a form of a signal and porosity of periodic impulses. Sources of signals of ShIM are the devices given below on illustrations:
Devices of stabilization of turns of idling (IAC)
Primary winding of the coil of ignition
Electromagnetic valve of a purge of a coal adsorber (EVAP)
Valves of system of recirculation of the fulfilled gases (EGR)
The coded sequence of rectangular impulses Performance data are amplitude, frequency and a form of sequence of separate impulses. Signals of this sort are generated by the module of memory of self-diagnostics of ECM of a control system of the engine. Amplitude and form of a signal remain constants, the written-down value will be given until memory of the module is not cleared. Interpretation of oscillograms The form of the signal which is given out by an oscillograph depends on a set of various factors and can change considerably. In a look told before starting replacement of the suspected component in case of discrepancy of a form of the removed diagnostic signal with the reference oscillogram, it is necessary to analyse carefully received result (address to illustrations below).
Tension Zero level of a reference signal cannot be considered as absolute basic value, – "zero" real signal, depending on concrete parameters of the checked chain, it can be shifted rather reference ([1] – address to an illustration the Digital signal) within a certain admissible range. Full amplitude of a signal depends on supply voltage of the checked contour and also can vary in certain limits of rather reference value ([3] – address to an illustration the Digital signal and [2] – address to an illustration the Analog signal). In chains of a direct current the range of a signal is limited to supply voltage. It is possible to give a chain of system of stabilization of turns of idling (IAC) which alarm tension does not change with change of turns of the engine in any way as an example. In chains of alternating current signal amplitude already unambiguously depends on the frequency of operation of a source of a signal, so, amplitude of the signal which is given out by the sensor of provision of a cranked shaft (CKP) will increase with increase of turns of the engine. In a look told if amplitude of the signal removed by means of an oscillograph is excessively low or high (up to trimming of top levels), it is only enough to switch the working range of the device, having passed to the corresponding scale of measurement. When checking the equipment of chains with electromagnetic management (for example, IAC system) at power off tension throws ([4] – address to an illustration the Digital signal), which in the analysis of results of measurement can be ignored quietly can be observed. It is not necessary to worry also at emergence of such deformations of the oscillogram, as bevelling of the lower part of the forward front of rectangular impulses ([5] – address to an illustration the Digital signal) if, of course, the fact of a vypolazhivaniye of the front is not a sign of violation of serviceability of functioning of the checked component. Frequency Frequency of repetition of alarm impulses depends on the working frequency of a source of signals. The form of the removed signal can be edited and brought to a look, convenient for the analysis, by switching on an oscillograph of scale of temporary development of the image. At supervision of signals in chains of alternating current temporary development of an oscillograph depends on the signal source frequency ([3] – address to an illustration the Analog signal) determined by engine turns. As it was already told above, for reduction of a signal to a legible look it is enough to switch the scale of temporary development of an oscillograph. In certain cases the oscillogram of a signal appears rather reference dependence developed specularly that is explained by reversibility of polarity of connection of the corresponding element and, in the absence of a ban on change of polarity of connection, can be ignored in the analysis. Typical signals of components of control systems of the engine Modern oscillographs are usually equipped with only two alarm wires together with a set of the various probes allowing to carry out connection of the device practically to any device. The red wire is connected to a positive pole of an oscillograph and is usually connected to the plug of the electronic module of management (ECM). The black wire should be connected to reliably grounded point (weight). Injectors Control of composition of air and fuel mix in modern automobile electronic systems of injection of fuel is exercised by timely adjustment of duration of opening of electromagnetic valves of injectors. Often on the oscillogram it is possible to observe also a series of the short pulsations following directly the initiating negative rectangular impulse and supporting the electromagnetic valve of an injector abroach, and also the sharp positive throw of tension accompanying the moment of closing of the valve. Serviceability of functioning of ECM can be easily checked by means of an oscillograph by visual supervision of changes of a form of the operating signal at a variation of working parameters of the engine. So, duration of impulses at an engine provorachivaniye on single turns has to be slightly higher, than during the operation of the unit on low turns. Increase of turns of the engine has to be followed by corresponding increase in time of stay of injectors abroach. This dependence is especially well shown when opening a butterfly valve by short pressing a gas pedal.
Fast closing of a butterfly valve has to lead to the oscillogram flattening confirming the fact of an overshoot of injectors (for systems with fuel supply trim). At cold start the engine needs some enrichment of air and fuel mix that is provided with automatic increase in duration of opening of injectors. In process of warming up duration of the operating impulses on the oscillogram has to be reduced continuously, gradually coming nearer to value, typical for single turns. In systems of injection in which the injector of cold start is not applied, at cold start of the engine the additional operating impulses which are shown on the oscillogram in the form of pulsations of variable length are used. Typical dependence of duration of the operating impulses of opening of injectors on a working condition of the engine is presented in the table given below.
Inductive sensors
The increase in turns of the engine has to be followed by increase in amplitude of the pulse signal developed by the sensor. Electromagnetic valve of stabilization of turns of idling (IAC) In automotive industry electromagnetic IAC valves of a set of various types which are giving out signals of also various form are used. The common distinctive feature of all valves is that fact that porosity of a signal has to decrease with increase of the load of the engine connected with inclusion of the additional consumers of power causing decrease of turns of idling. If porosity of the oscillogram changes with increase in loading, however at inclusion of consumers violation of stability of turns of idling takes place, check a condition of a chain of the electromagnetic valve, and also correctness of the given-out ECM of a command signal. Usually in chains of stabilization of turns of idling the 4-polar step electric motor which description is given below is used. Check of 2-contact and 3-contact IAC valves is made in a similar manner, however oscillograms of the alarm tension which is given out by them are absolutely unlike. Step electric motor, reacting to the given-out ECM the pulsing operating signal, makes step correction of turns of idling of the engine according to the working temperature of cooling liquid and the current load of the engine. Levels of the operating signals can be checked by means of an oscillograph which measuring probe is connected serially to each of four plugs of the step motor. Lambda probe (oxygen sensor)
If the removed signal is not wavy, and represents linear dependence, that, depending on tension level, it testifies to excessive reimpoverishment (0 – 0.15 In), or reenrichment (0.6 – 1 In) air and fuel mix. If on single turns of the engine the normal wavy signal takes place, try to squeeze out several times sharply loops of gas, fluctuations of a signal should not exceed the limit of the range of 0 - 1 Century. The increase in turns of the engine has to be followed by increase of amplitude of a signal, reduction – decrease. Sensor of a detonation (KS)
Ignition signal at the exit of the amplifier of ignition
At increase in turns of the engine the frequency of a signal has to increase in direct ratio. Primary winding of the coil of ignition
Unevenness of throws can be caused by the excessive resistance of a secondary winding, and also malfunction of a condition of VV of a wire of the coil or a candle wire. |
|