Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical box передч
3.3. Automatic transmission
3.3.1. General information
3.3.2. Hydrotransformer
3.3.3. Main transfer
3.3.4. Adjustment of a cable of the selector of switching of automatic transmission
3.3.5. Designation of an automatic transmission (AF 13-II)
3.3.6. Check of a condition of transmission oil (AF13-II)
3.3.7. Check of pressure of oil (AF13-II)
3.3.8. Check of the item switch of the lever of gear shifting (AF13-II)
3.3.9. Unblocking of a stopper of the lever of gear shifting at violation of its work
3.3.10. Adjustment of the item switch of the lever of gear shifting (AF13-II)
3.3.11. Adjustment of hummock system of a drive of gear shifting (AF13-II)
3.3.12. Replacement of hummock system of a drive of gear shifting (AF13-II)
3.3.13. Replacement of the switch of the lock adaptation of the lever of gear shifting
3.3.14. Replacement of a plait of wires in knot of the lever of gear shifting (AF13-II)
3.3.15. Replacement of the control unit of the check point electronic switch
3.3.16. Replacement of the filament lamp of the indicator of gear shifting in the console of the lever of gear shifting (AF 13-II)
3.4. Driving mechanism
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 












3-3-10-regulirovka-pozicionnogo-pereklyuchatelya-rychaga-pereklyucheniya-peredach-af13-ii.html

3.3.10. Adjustment of the item switch of the lever of gear shifting (AF13-II)

Dismantle the holder of the socket of a plait of wires 2.
Release and disconnect the socket of a plait of wires of the item switch of the lever of gear shifting 1.
Wring out from a control lever a cable of a drive of gear shifting 3.
Establish KM-962-A adaptations with KM-962-10.
Connect to the socket of a plait of wires of the item switch of the lever of gear shifting.
Connect to the accumulator.
Transfer the gear shifting lever by rotation of a control lever 2 to neutral situation.

NOTE
First of all, the lever of gear shifting needs to be turned to the left against the stop (in the movement direction), right after it to turn back on 2 lock positions («P», «R», «N»). For position of the lever "N" the light-emitting diodes corresponding to marks in the sliding table should light up.

For adjustment turn off lock screws 1.

NOTE
Turn the item switch of the lever of gear shifting so that all light-emitting diodes corresponding to position of the lever "N" lit up.

Tighten lock screws – 25 N · m.

NOTE
Make switching of consistently all transfers by control lever turn. For each separate position of the lever of gear shifting the light-emitting diodes corresponding to marks should light up. If necessary procedure of adjustment repeat.

Dismantle KM-962-A adaptations with KM-962-10.
Disconnect from the accumulator.
Disconnect from the socket of a plait of wires of the item switch of the lever of gear shifting.
Establish the socket of a plait of wires of the item switch of the lever of gear shifting 1.
Attach and fix the socket of a plait of wires.
Tighten fastening of the socket of a plait of wires of 2-20 N · m.
Establish a hummock wire of system of a drive of gear shifting 3 on a control lever of the item switch of the lever of gear shifting.

«on page back
3.3.9. Unblocking of a stopper of the lever of gear shifting at violation of its work
on the following page»
3.3.11. Adjustment of hummock system of a drive of gear shifting (AF13-II)