Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.10.1. Removal and installation of fuel nozzles
2.10.2. Replacement топливопровода a high pressure (The pump of a high pressure – the pressure head chamber)
2.10.3. Module of the fuel pump
2.10.4. Replacement of the module of a dosage
2.10.5. Replacement of a regulator of pressure of fuel
2.10.6. Replacement of the dempfiruyushchy case of return of fuel
2.10.7. Fuel level sensor replacement
2.10.8. Fuel tank
2.10.9. Replacement of a tube of a jellied mouth of a fuel tank (petrol engines)
2.10.10. Catching system паров fuels
2.10.11. Replacement of a forward ventilating tube
2.10.12. Removal and capacity installation with absorbent carbon
2.10.13. Removal and installation of the sensor of a mass consumption of air
2.10.14. Release system (Z 14 XEP, Z 14 XEL, Z 16 XEP)
2.10.15. System of release (Z18 XE)
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 












2-10-7-zamena-datchika-urovnya-topliva.html

2.10.7. Fuel level sensor replacement

Removal
Open a cowl.
Disconnect the storage battery.
Disconnect a weight clip from a weight conclusion.
Place below the container for plum.
Dump pressure of fuel, using the special KM-J-34730-91 adaptation via the test channel.

NOTE
Collect following fuel in the suitable container – observe safety rules and the national legislation.

Open both back doors
Remove a many-placed unseparable seat.
Extend 2 brackets of release.
Remove from an arm in the direction of arrows in 2 places.
Take out a many-placed unseparable seat from the car.
Uncover.
Bend a noise isolation and open a cover.
Disconnect the socket of a plait of wires.
Mark топливопроводы and remove with use of the special KM-796-A tool.
Close топливопроводы caps of the KM special tool 807 and KM 6015.

NOTE
Make sure that the KM special tool 797 properly and is reliably established.

Weaken a lock ring of a cover using the KM special tool 797.

NOTE
Rotate counter-clockwise.

Accurately uncover the module up.

NOTE
Watch to damaging wires and hoses.

Disconnect 2 sockets of a plait of wires from a cover.

NOTE
The special KM-6391-1 tool should be established so that the sensor in a tank moved a vertical. Establish the special KM-6391-1 tool 4 and take out the module.

Remove the module, using the KM special tool 6391.
Establish the special tool of 4 KM 6391 on the module, as is shown in drawing.
Release the module in pressing the special tool and remove it.
Take out the module from a fuel tank.
Remove the fuel level sensor and release holders.

NOTE
Do not pull for a fuel level sensor shaft.

Accurately extend from the arrow directing in the direction.

Installation
Establish the fuel level sensor.
Establish in the directing.
Establish the module.
Establish in 4 latches 1.

NOTE
Latches should contact with click.

Connect 2 sockets of a plait of wires with a cover.
Close a module cover a lock disk.
Establish a cover with new laying, using the KM special tool 797.
Rotate clockwise.
Connect топливопроводы and connect the quick disconnect coupling.
Connect the socket of a plait of wires.
Close a cover.
Unbend aside a noise isolation.
Establish a back many-placed unseparable seat.
Fix 2 clips.
Press down and block on a place.
Close both back doors.
Connect the storage battery.
Connect a weight clip to a weight conclusion.
Program volatile memory.
Close a cowl.

«on page back
2.10.6. Replacement of the dempfiruyushchy case of return of fuel
on the following page»
2.10.8. Fuel tank