Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.10.1. Removal and installation of fuel nozzles
2.10.2. Replacement топливопровода a high pressure (The pump of a high pressure – the pressure head chamber)
2.10.3. Module of the fuel pump
2.10.4. Replacement of the module of a dosage
2.10.5. Replacement of a regulator of pressure of fuel
2.10.6. Replacement of the dempfiruyushchy case of return of fuel
2.10.7. Fuel level sensor replacement
2.10.8. Fuel tank
2.10.9. Replacement of a tube of a jellied mouth of a fuel tank (petrol engines)
2.10.10. Catching system паров fuels
2.10.11. Replacement of a forward ventilating tube
2.10.12. Removal and capacity installation with absorbent carbon
2.10.13. Removal and installation of the sensor of a mass consumption of air
2.10.14. Release system (Z 14 XEP, Z 14 XEL, Z 16 XEP)
2.10.15. System of release (Z18 XE)
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293



2-10-5-zamena-regulyatora-davleniya-topliva.html

2.10.5. Replacement of a regulator of pressure of fuel

Removal
Remove an inlet collector, having unscrewed a fastening bolt.
Remove a ventilating hose of the engine from a cover of a head of the block of cylinders.
Disconnect an inlet pipe from an air inlet hose.
Disconnect an inlet pipe from a turbonagnetatel.

NOTE
Close an inlet pipe of a turbonagnetatel.

Remove an inlet pipe.
Dump pressure of fuel via the test union using the device for check of tightness of KM-J-34730-91.
Collect following fuel in the suitable container.
Disconnect the vacuum highway (1) from a regulator of pressure of fuel (2). Remove a collar of fastening (5) from a regulator of pressure of fuel and a fuel stage.
Mark adjusting situation and accurately remove a regulator of pressure of fuel from a fuel stage.

NOTE
In this point absolute purity is extremely important.

Replace sealing rings.

Installation
Before installation cover sealing rings with a thin layer of silicone greasing (white).
Note the adjusting provision of a regulator of pressure of fuel. Establish a regulator of pressure of fuel in a fuel stage.

NOTE
In this point absolute purity is extremely important.

Establish a collar of fastening of a regulator of pressure of fuel and attach a fuel stage, tighten the moment of 5 N · m.
Connect a vacuum hose to a regulator of pressure of fuel.
Remove a cap of an inlet pipe of a turbonagnetatel.
Attach a ventilating hose of the engine to a cover of a head of the block of cylinders and fix a collar.
Attach an inlet pipe to a turbonagnetatel.
Attach an inlet pipe to an air inlet hose.
Wrap a bolt of fastening of a collar.


«on page back
2.10.4. Replacement of the module of a dosage
on the following page»
2.10.6. Replacement of the dempfiruyushchy case of return of fuel