Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.10.1. Removal and installation of fuel nozzles
2.10.2. Replacement топливопровода a high pressure (The pump of a high pressure – the pressure head chamber)
2.10.3. Module of the fuel pump
2.10.4. Replacement of the module of a dosage
2.10.5. Replacement of a regulator of pressure of fuel
2.10.6. Replacement of the dempfiruyushchy case of return of fuel
2.10.7. Fuel level sensor replacement
2.10.8. Fuel tank
2.10.9. Replacement of a tube of a jellied mouth of a fuel tank (petrol engines)
2.10.10. Catching system паров fuels
2.10.11. Replacement of a forward ventilating tube
2.10.12. Removal and capacity installation with absorbent carbon
2.10.13. Removal and installation of the sensor of a mass consumption of air
2.10.14. Release system (Z 14 XEP, Z 14 XEL, Z 16 XEP)
2.10.15. System of release (Z18 XE)
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293



2-10-2-zamena-toplivoprovoda-vysokogo-davleniya-nasos-vysokogo-davleniya-napornaya-kamera.html

2.10.2. Replacement топливопровода a high pressure (The pump of a high pressure – the pressure head chamber)

ATTENTION
At work with Common Rail system wait within one minute after engine switching off. The system dumps pressure automatically.

ATTENTION
At work with fuel observe purity as even very small particles of dirt can result in malfunctions in operation of the engine or system. Close open unions of fuel system suitable caps. Repeated application of caps is not allowed.


Removal
Open a cowl.
Disconnect the storage battery.
Disconnect earthing connector from a grounding clip.
Uncover the engine
Remove an inlet pipe.
Disconnect 3 plaits of wires.
Disconnect a ventilating hose of the engine.
Disconnect the quick disconnect coupling.
Disconnect from a hose of an air inlet of a turbonagnetatel.
Weaken a collar.
Disconnect from an air inlet hose, the sensor of a mass consumption of air.
Weaken a collar and unscrew 2 bolts of fastening.
Place below the container for plum.
Disconnect the pipeline of a high pressure from the pump of a high pressure to the pressure head chamber. Unscrew 2 connecting nuts.

Installation
Establish the pipeline of a high pressure from the pump of a high pressure to the pressure head chamber.
Use the new pipeline of a high pressure.
Tighten a connecting nut of M14 the moment of 19 N · m.
Tighten a connecting nut of M12 the moment of 24 N · m.
Establish an inlet pipe.
Attach to a hose of an air inlet of a turbonagnetatel.
Tighten a collar the moment of 3.5 N · m.
Attach the sensor of a mass consumption of air to an air inlet hose.
Tighten a collar the moment of 3.5 N · m.
Attach a ventilating hose of the engine.
Fix a collar.
Tighten 2 bolts of fastening.
Fix 3 plaits of wires.
Establish an engine cover.
Connect the storage battery.
Attach earthing connector to a grounding clip.
Tighten a fastening nut.
Program volatile memory.
Close a cowl.

«on page back
2.10.1. Removal and installation of fuel nozzles
on the following page»
2.10.3. Module of the fuel pump