Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.4.1. Removal and installation of the case of the oil filter (Z10XE, Z10XEP, without the conditioner)
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)
2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without the conditioner)
2.4.4. Replacement of the relay of pressure of oil (Z10XE, Z10XEP)
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








Лучшие материалы для водонепроницаемой одежды
99e20293



2-4-3-snyatie-i-montazh-maslyanogo-poddona-z10xe-z10xep-bez-kondicionera.html

2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without the conditioner)

Removal
Open a cowl.
Lift the car.

NOTE
On option of the ECO model dismantle a cover of motor office below.

Merge engine oil.
Substitute the reception pallet.
Turn off a carving stopper of a drain opening.
Release an exhaust system.

NOTE
At removal of the average exhaust silencer, the catalyst, a final collector or a final collector with the catalyst it is necessary to secure a part of system of release of OG remaining in the car against uncontrollable sagging.

For this purpose the part of system of release of OG with the flexible tube which was in it can be fixed suitable means, for example, by means of a wire on a running gear.

NOTE
Bend of a flexible tube even on 5-10 angular degrees in relation to the provided assembly position can cause damage of a flexible hose with the subsequent failure.

Disconnect the socket of a plait of wires a lambda sensor of control of the catalyst 1.
Disconnect system of exhaust gases – 2 dempfiruyushchy partitions (arrows).
Dismantle an exhaust pipe in front 2.
Turn off 3 nuts.
Exhaust pipe in front attach to the case of the forward bridge at the left.
Remove a casing of a poliklinovy belt.
Unscrew 3 bolts of fastening 1.
Dismantle a clip (shooter).
Twirl a carving stopper of a drain opening for engine oil.
Replace a sealing ring.
Tighten a bolt the moment of 10 N · m.
Dismantle the oil pallet.
On a transmission unscrew 3 bolts of fastening 1.
On a support of a cranked shaft turn off 14 bolts of fastening.
Installation
Establish the oil pallet.
Replace consolidation.
Twirl 17 bolts of fastening.

NOTE
Observe sequence of an inhaling of bolts of fastening.

On a support of a cranked shaft tighten 14 bolts of fastening the moment of 10 N · m.
On a transmission tighten 3 bolts of fastening the moment of 40 N · m.
Establish an exhaust system.
Replace consolidation.
Replace nuts.
Tighten 3 nuts the moment of an inhaling of 20 N · m.
Attach dempfiruyushchy partitions.
Connect the socket of a plait of wires a lambda sensor of control of the catalyst.
Establish a casing of a poliklinovy belt.

NOTE
On option of the ECO model establish a cover of motor office below.

Tighten bolts.
Establish a clip.
Lower the car.
Fill in engine oil.
Start the engine and leave to work until the control lamp of pressure of oil will go out.
Check and, if necessary, modify level of engine oil.
Close a cowl.

«on page back
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)
on the following page»
2.4.4. Replacement of the relay of pressure of oil (Z10XE, Z10XEP)