Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.4.1. Removal and installation of the case of the oil filter (Z10XE, Z10XEP, without the conditioner)
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)
2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without the conditioner)
2.4.4. Replacement of the relay of pressure of oil (Z10XE, Z10XEP)
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








Душевые перегородки из HPL пластика 99e20293



2-4-1-snyatie-i-montazh-korpusa-maslyanogo-filtra-z10xe-z10xep-bez-kondicionera.html

2.4.1. Removal and installation of the case of the oil filter (Z10XE, Z10XEP, without the conditioner)

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It it is necessary откалибровать anew.

Lubricant contour
* the Engine is heated-up and idles

Lubricant contour
* the Engine is heated-up and idles

Removal
Open a cowl.
Disconnect plugs of the storage battery.
Disconnect a weight wire.
Dismantle heated up a lambda sensor of regulation of structure of a fuel mix.
Disconnect the socket of a plait of wires.
Release a plait of wires.
Carefully turn out by means of the KM-61291 adaptation.
Dismantle a transport earring of the engine at the left 2.
Turn out a bolt.
Dismantle a guard of a final collector.
Turn off 3 bolts of fastening.
Directing tube щупа an oil meter turn forward.
Uncover cases of the oil filter.

NOTE
On option of the ECO model uncover motor office below.

Substitute the reception pallet.
Remove the case of the oil filter.
Turn off 3 bolts of fastening (shooters).
Clean sealing surfaces of the case of the oil filter, the block of cylinders.

Installation
Establish the case of the oil filter.
Replace consolidation.
Tighten bolts the moment of an inhaling of 20 N · m.
Establish a cover of the case of the oil filter.
Replace a sealing ring.
Tighten bolts of fastening of a cover the moment of 10 N · m.
Establish a guard of a final collector.
Establish directing tube щупа an oil meter.
Tighten 3 bolts of fastening the moment of 8 N · m.
Establish a transport earring of the engine at the left.
Establish heated up a lambda sensor of regulation of structure of a fuel mix.
Put on a carving assembly paste (white).
Tighten a lambda sensor the moment of 40 N · m.
Attach the socket of a plait of wires.
Fix a plait of wires.
On option of the ECO model establish a cover of motor office below.
Connect plugs of the storage battery.
Program volatile memory.
Close a cowl.

«on page back
2.4. Greasing system
on the following page»
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)