|
1-7-14-ehlektricheskoe-oborudovanie.html
1.7.14. Electric equipment
Electronic systems of ignition work with very high capacity of the category. Do not touch them, it is life-threatening.
Safety locks
The defective safety lock can be distinguished on the burned-down fusible thread. Replacement of a safety lock make only after elimination of a cause of defect.
Box of safety locks
The box of safety locks is located in motor office near a broad tank of cooling liquid.
Risfiksiruyte a cover of a box of the main safety locks for a loop also remove up.
Remove an additional cover.
It is recommended to have always with itself a complete set of safety locks.
Spare safety locks place in a box of safety locks in the place provided for this purpose, to the right of it there is a stripper for replacement of safety locks.
Before replacement of a safety lock disconnect the corresponding switch or switch off ignition.
Establish the adaptation for a pulling of safety locks on a safety lock and take out it.
Insert safety locks only the specified nominal current. Its value is specified on each safety lock and is in addition marked by color, and also designated on a seat in a box of safety locks.
Safety locks and the major chains with safety locks
Color marking and current of safety locks
|
NOTE
Some electric chains can be protected by several safety locks.
|
|
ATTENTION
Before replacement of a lamp switch off ignition and the corresponding switch.
|
Replacement of lamps
New lamp take only for a socle. Do not take a lamp for glass barehanded, otherwise on glass there are traces of fingers. Dirt settles on a reflector and worsens its reflective ability. Remove traces of a touch with the pure not fibrous fabric impregnated with alcohol.
Replaceable lamp подобирайте according to marking on a socle of a defective lamp. Do not exceed the specified capacity in watts.
Replacement of extreme lamps of the forward block of headlights is made through apertures in a forward wheel niche. For this purpose turn wheels in the necessary party, release a clamp and uncover.
Adjustment of headlights
At regulation of headlights regulation of a tilt angle of headlights should be established on 0.
In drawing headlights with separate systems of a passing beam 1 (external lamps) and a driving beam 2 (internal Pampas) are represented.
Replacement of lamps of a passing beam
Open and prop up a cowl.
At replacement of Pampas on the left side open a cover of a box of safety locks.
At lamp replacement on the right side remove a hose from the air filter. Extend up a refueling branch pipe of a tank of the device of washing of headlights.
To unscrew a cover to the left and remove it.
Press Pampas for the tip down.
Take out the filament lamp with the tip from the reflector case.
Remove the tip from a socle of lamps.
Insert the tip into the new filament lamp, without touching thus glass of Pampas.
Insert a new lamp with the tip so that the fixing ledge entered into dredging on a reflector.
Establish and close a protective cap of headlights.
After lamp replacement on the left side close a cover of a box of safety locks.
After lamp replacement on the right side establish and fix a hose on the air filter. Establish into place a refueling branch pipe of a tank of the device of washing of headlights.
Replacement of lamps of a driving beam
Open and prop up a cowl.
At lamp replacement on the left side open a koyshka of a box of safety locks.
At lamp replacement on the right side remove a hose from the air filter.
Unscrew a cover to the left and remove it.
To disconnect the tip from a lamp.
Release a spring bracket from a fixing ledge forward and turn aside.
Take out the filament lamp from the boss.
At installation of a new lamp insert fixing ledges into reflector cuts, thus not to touch lamp glass.
Fix a spring wire bracket, insert the tip into a lamp.
Establish and close a protective cap of headlights.
After replacement of Pampas on the left side close a cover of a box of safety locks.
After replacement of Pampas on the right side establish and fix a hose on the air filter.
System of halogen headlights (replacement of lamps of a parking light)
Open and prop up a cowl.
At lamp replacement on the left side open a cover of a box of safety locks.
At lamp replacement on the right side remove a hose from the air filter.
Turn a cap of a headlight of a driving b | 