Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
7.1. Power supply system
7.1.1. General information
7.1.2. Storage battery
7.1.3. Generator
7.1.4. Removal and generator installation (the Z18XE engine, with the conditioner)
7.1.5. Replacement of a driving pulley of the generator
7.1.6. Replacement of a regulator of the generator (the Z18XE engine, with the conditioner)
7.1.7. Generator check
7.1.8. Starter replacement (Z10XE, Z 10 XEP, without the conditioner)
7.1.9. Removal and starter installation (Z14XE, Z16YNG, with the conditioner)
7.2. Lighting system
7.3. Onboard electric equipment
8. Body
9. Electric equipment schemes
 












7-1-8-zamena-startera-z10xe-z-10-xep-bez-kondicionera.html

7.1.8. Starter replacement (Z10XE, Z 10 XEP, without the conditioner)

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It is necessary to calibrate it anew.

Removal
Open a cowl.
Disconnect the accumulator.
Disconnect a weight wire.
Lift the car.
Remove a casing of a poliklinovy belt.

NOTE
On option of the ECO model uncover motor office below.

Unscrew 3 bolts of fastening 1.
Dismantle a clip (shooter).
Remove a poliklinovy belt.

NOTE
Mark the rotation direction.

The tension device of a poliklinovy belt by means of KM-6131 pull in the arrow direction.
Remove from a pulley poliklinovy ременя a cranked shaft.
Insert KM-955-21.
Weaken a tension of the tension device of a poliklinovy belt.
Remove the tension device of a poliklinovy belt.
Turn out the screw 2.
Disconnect the socket of a plait of wires a lambda sensor of control of the catalyst.
Remove cable collars.
Unscrew a plait of wires of the generator 1.
Turn off 2 nuts.
Dismantle the generator.
Turn off 2 carving connections.
Carefully remove the generator, having pulled down.
Disconnect a plait of wires of a starter.
Turn off 2 nuts 1.
Dismantle a starter.
Turn off 2 bolts of fastening (shooters).

Installation
Establish a starter.
Tighten 2 bolts of fastening of 25 N · m.
Fix a plait of wires of a starter.
Tighten 2 nuts.
Establish the generator.
Tighten 2 carving connections of 35 N · m.
Fasten a plait of wires of the generator.
Tighten 2 nuts.
Connect the socket of a plait of wires a lambda sensor of control of the catalyst.
Establish cable collars.
Establish the tension device of a poliklinovy belt.
Tighten the screw of 20 N · m.
Establish a poliklinovy belt.

NOTE
Observe the direction of rotation and assembly situation.

Pull the tension device of a poliklinovy belt by means of KM-6131.
Remove KM-955-2.
Weaken a tension of the tension device of a poliklinovy belt.
Establish a casing of a poliklinovy belt.

NOTE
On option of the ECO model establish a cover of motor office below.

Tighten 3 bolts of fastening.
Establish a clip.
Lower the car.
Connect the accumulator.
Close a cowl.
Program volatile memory.

«on page back
7.1.7. Generator check
on the following page»
7.1.9. Removal and starter installation (Z14XE, Z16YNG, with the conditioner)