Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. General information
4.2. Wheels and tires
4.3. Running gear
4.4. Forward suspension bracket
4.4.1. Removal and installation of the stabilizer of the forward bridge
4.4.2. Removal and installation of a rotary fist
4.4.3. Removal and installation of the lever of an independent suspension bracket
4.4.4. Replacement of all rubber bearings of the stabilizer
4.4.5. Removal and installation of an amortization rack with the shock-absorber
4.4.6. Dismantling and assembly of an amortization rack
4.5. Back suspension bracket
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293



4-4-2-snyatie-i-ustanovka-povorotnogo-kulaka.html

4.4.2. Removal and installation of a rotary fist

Removal
Remove a forward wheel.
Note situation concerning a wheel nave.
Removal of a semi-axis from a wheel nave.
Remove a dust cap.

NOTE
The dust cap does not act in film without damages.

Remove lock шплинт 2 from a semi-axis 3 nut.
Establish the KM-6610 adaptation on a wheel nave two screws of a wheel 4.
Remove a semi-axis 3 nut, hold KM-6610 5 together with the KM-956-16 extension piece.
Remove the KM-6610 adaptation.
Remove a brake disk.
Remove a head of cross-section steering draft.
Establish the CH-47658 2 adaptation in the correct situation.

NOTE
Center by means of a nozzle of a face key.

Use the suitable plug 4. The plug 4 should adjoin densely to the lever of cross-section steering draft 3. Tighten the CH-47658 2 adaptation for a shestigrannik 1.
Unscrew a nut 5.
Remove CH-47658 2, weaken c the help of a shestigrannik 1.
Remove the holder of the wheel sensor 1 with the ABS wheel sensor from a rotary fist.
Unscrew the screw.
Remove a head of cross-section steering draft 2.
Remove the adaptation KM-507-C 3 from a rotary fist.
Remove a rotary fist from the directing hinge.
Unscrew a nut with the screw 4.
Remove a basic pipe of an amortization rack from a rotary fist.

NOTE
At replacement of a rotary fist reinstall closing plate of a brake disk and use the new bearing of a wheel.

Unscrew 2 nuts with the screw 5.

Installation
Establish a rotary fist 1.
Insert a rotary fist into directing hinge of the lever of an independent suspension bracket 2.
Deduce a semi-axis 3 in a wheel nave.
Establish a basic pipe of an amortization rack on a rotary fist, tighten 2 new screws of a nut of 4 80 N · m + 60 ° +15 °.
Tighten the screw 7 of the directing hinge of 60 N · m.
Use a new nut.
Establish a head of cross-section steering draft 6 on a rotary fist.
Establish the CH-47658 adaptation in the correct situation.

NOTE
Center by means of a nozzle of a face key. Use the suitable plug. The plug should adjoin to the lever of cross-section steering draft densely. Tighten the CH-47658 adaptation for a shestigrannik.

Tighten a nut of 35 N · m.
Remove the CH-47658 adaptation, weaken its fastening of c by the help of a shestigrannik.
Establish the holder of the wheel sensor 5 with the ABS wheel sensor on a rotary fist of 8 N · m.
Establish a brake disk.
Fix a semi-axis on a wheel nave.
Establish KM-6610 1 with 2 screws of a wheel on a wheel nave.
Tighten a new koronchaty nut 1 and a washer 2 on a semi-axis of 120 N · m.
Hold the KM-6610 4 adaptation together with the extension piece KM-956-1 6.
Weaken a koronchaty nut 1 while the koronchaty nut 1 will not turn by hand.
Tighten a koronchaty nut of 1 20 N · m + 90 °.
Establish new lock шплинт.

NOTE
If it is necessary, turn a koronchaty nut 1 back until the opening under шплинт will not rise coaxially with the following cut of a koronchaty nut.

Remove the KM-66104 adaptation.
Establish a new dust cap 5 on a wheel nave.
Establish a forward wheel – the moment of an inhaling of 110 N · to m.

«on page back
4.4.1. Removal and installation of the stabilizer of the forward bridge
on the following page»
4.4.3. Removal and installation of the lever of an independent suspension bracket