Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.5. Injection system
2.5.1. Replacement of fuel nozzles (one or all) (Z10XE, Z10XEP, without the conditioner)
2.5.2. Replacement of the fuel filter (petrol engines)
2.5.3. Removal and installation of the electric fuel pump
2.5.4. Replacement of consolidation of a final collector (Z10XE, Z10XEP, without the conditioner)
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293



2-5-2-zamena-toplivnogo-filtra-benzinovye-dvigateli.html

2.5.2. Replacement of the fuel filter (petrol engines)

Removal
Remove an air line guard from the bottom of a body of Century.
Release the fuel filter in the holder.
Remove a bolt 1.

NOTE
In drawings the modeling Combo option (is shown to F06, by F25).

Establish a head of the special tool 1 on the fuel filter 2.
The carving union 3 specifies down.
Press all surface of rubber consolidation (shooter) the case of the fuel filter.
Adjust as appropriate a coupler.
Tighten it a tightening bracket.
Establish a vessel for collecting fuel 3 on a head of the special tool 1.

ATTENTION
The fuel filter is under pressure. Check the special tool on durability of landing.

Fix a vessel for collecting fuel on a carving branch pipe and to tighten.

NOTE
The built-in drill bores through the case of the fuel filter. Following fuel flows down in a reception vessel.

Blow the fuel filter.

ATTENTION
Observe the set sequence.

By means of the pincers 5 attached to the special tool, do wider opening above (shooter).
Remove from the fuel filter and cork 2 топливопровода (2, 4).

ATTENTION
Remove топливопроводы only when fuel is not issued any more from the fuel filter.

Dismantle by means of the KM-796-A adaptation from quick disconnect connection.
Cork топливопровод by means of the KM-807 adaptation.
When the fuel filter will be emptied, remove the special tool.
Remove a reception vessel.
Remove a head of the special tool – weaken a tension collar.
Remove the fuel filter.

Installation
Insert 2 new connecting clips 1 into the plug of a high-speed lock топливопровода 2.
Insert the new fuel filter.
Insert in front in the holder.

NOTE
Observe the throughput direction.

Connect 2 топливопровода (4, 5) to the fuel filter.
Snimitespetsialnoye KM-807 adaptation.
Connect 2 топливопровода by means of a high-speed lock to the fuel filter.
Carry out test for stretching.

NOTE
Be convinced that high-speed locks were correctly fixed.

Fix the fuel filter in the holder.
Establish a bolt 3 and tighten it the moment of 4 N · m.
Establish an air line guard on the body bottom.

For modeling ECO option
At the working engine check 2 high-speed locks топливопровода in the fuel filter on tightness.

«on page back
2.5.1. Replacement of fuel nozzles (one or all) (Z10XE, Z10XEP, without the conditioner)
on the following page»
2.5.3. Removal and installation of the electric fuel pump