|
8-3-1-snyatie-i-ustanovka-ili-zamena-vetrovogo-stekla.html
8.3.1. Removal and installation or windscreen replacementRemoval
|
NOTE
In this case windscreen removal by means of system of removal of BO-46974 is described.
|
|
ATTENTION
In order to avoid a travmirovaniye of eyes and hands before the beginning of works put on working gloves and goggles.
|
|
NOTE
Put the car on an equal surface and establish exactly forward wheels.
|
Remove both levers of a screen wiper.
Remove 2 protective caps.
Turn off 2 nuts.
Take levers of a screen wiper 1.
Completely dismantle a water repeller.
Remove consolidation of motor office 4.
Turn off 2 screws крепленияа a water repeller of 2 (shooters).
Pull together a hose of a fuel nozzle 3.
Remove both decorative levels of a windscreen.
Pull together a decorative level of a windscreen sideways from a forward rack.
Extend from a ceiling level 1 decorative level of a windscreen sideways and remove it.
Dismantle both internal coverings of a forward rack above 1.
|
NOTE
For cars with a head safety cushion the internal covering of a forward rack above in addition becomes stronger a frame. This frame 2 has Airbag inscription.
|
Release 3 clips.
Take a covering.
Remove an internal rear-view mirror.
Measure glass on a diagonal, cut off a string.
Cut off a string of quadruple length of 5600 mm.
Puncture with an opening pricker.
Pass a string and stretch in the direction of the middle of glass.
Lay a string cutting torch 1 on perimeter.
Fix a fibrous tape.
Puncture an opening under the second end of a string.
By means of a pricker 2 involve the second end of a string in car salon.
|
NOTE
The string cutting torch should be blocked внахлест.
|
Fix a windshield.
Bring cutting tool.
Bring a collar with 2 coils to the left part of a windscreen.
Pass a string cutting torch.
Attach a string cutting torch 1 to gate.
Switch a graggers and previously pull a cutting torch string.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Arrow the direction is shown are sharp a string cutting torch.
Bring cutting tool.
Bring a collar with 2 coils to the lower left part of a windscreen.
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
|
NOTE
Use greasing for a directing roller, on a curve the windshield is necessary cut out with the increased effort.
|
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Arrow the direction is shown are sharp a string cutting torch.
Bring cutting tool.
Establish a collar with 2 coils to the right lower part of a windscreen.
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Arrow the direction is shown are sharp a string cutting torch.
Bring cutting tool.
Establish a collar with 2 coils to the right part of a windscreen.
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
|
NOTE
Use greasing for a directing roller, on a curve the windshield is necessary cut out with the increased effort.
|
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Arrow the direction is shown are sharp a string cutting torch.
Bring cutting tool.
Establish a collar with 2 coils to the right top part of a windscreen.
Establish a collar with 1 coil to the left top part of a windscreen.
Pass the second end of a string and fix it.
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
|
NOTE
Use greasing for a directing roller, on a curve the windshield is necessary cut out with the increased effort.
|
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Cut out a windshield by means of a collar and 1 coil while the string cutting torch will not rise at coil height.
Shooters show the direction are sharp a string cutting torch.
Bring cutting tool.
Establish a collar with 2 coils to the left part of a windscreen under a collar with the coil.
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
Cut out a windshield by means of a collar and 2 coils while the string cutting torch will not rise at coil height.
Arrow the direction is shown are sharp a string cutting torch.
Bring cutting tool.
Establish a collar with 1 coil to the top right part of a windscreen.
|
NOTE
The string cutting torch should be blocked внахлест.
|
Switch a graggers and previously pull a string of a cutting torch 1.
|
NOTE
Watch the correct arrangement of a string of a cutting torch on a directing roller of a collar.
|
Cut out a windshield.
Cut further while the string cutting torch completely will not cut the glutinous roller.
Clean cutting tools.
Arrow the direction is shown are sharp a string cutting torch.
Attach the MKM-641 adaptation.
Remove a windshield.
Remove the MKM-641 adaptation.
Remove glass splinters.
To cut off the glutinous roller from a windscreen.
Remove the glutinous roller by means of an enclosed insmtrument 1 to прибл. 1 mm of thickness.
Cut off the glutinous roller from the car.
Remove the glutinous roller by means of an enclosed insmtrument 1 to прибл. 1 mm of thickness.
Eliminate damages of a paint and varnish covering.
Installation
Put a first coat.
|
NOTE
Put a first coat only on new glass.
|
Put the glutinous roller.
Make an incision a tuba edge so that the glutinous roller in thickness прибл turned out. 13 mm.
Insert glass by means of the MKM-641 adaptation.
Fix glass a fibrous tape.
Observe keeping time.
Establish a rear-view mirror.
Establish an internal covering of a forward rack above at the left and on the right.
Insert a covering.
Fix 3 clips.
Establish both decorative levels of a windscreen.
Mount a water repeller.
Tighten the 2nd screw of fastening.
Put on a hose of a fuel nozzle.
Establish consolidation of motor office.
Mount both levers of a screen wiper.
Tighten 2 nuts.
Establish 2 protective caps.
| 