Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Features of a design
8.2. Hinged elements
8.2.1. Removal and installation of a front bumper
8.2.2. Removal and installation of the holder of a forward beam (blow limiter)
8.2.3. Replacement covered
8.2.4. Removal and installation of a protective covering in a wing
8.2.5. Removal and installation of a rear bumper
8.2.6. Removal and installation of a molding of an entrance aperture
8.2.7. Removal and installation of a forward protective level
8.2.8. Removal and water repeller installation
8.2.9. Replacement of additional consolidation of a frame of a roof
8.2.10. Removal and cowl installation
8.2.11. Removal and installation of the lock of a forward door
8.2.12. Removal and installation of the external handle of a forward door
8.2.13. Replacement directing glasses of an elevating window of a forward door
8.2.14. Removal and installation of an internal covering of a forward door
8.2.15. Remove and establish a level of a crack of a window regulator of a forward / back door inside
8.2.16. Removal and installation of a bracket of the lock of a forward door
8.2.17. Removal and installation of consolidation of a forward door
8.2.18. Removal and installation of a back door
8.2.19. Removal and installation of an internal covering of a back door
8.2.20. Removal and installation of consolidation of a back door
8.2.21. Removal and installation of a back folding door
8.2.22. Removal and installation of the lock of a back folding door
8.2.23. Removal and installation of the external handle of a back folding door
8.2.24. Removal and installation of a pneumatic spring of a back folding door
8.2.25. Removal and installation of consolidation of a back folding door
8.2.26. Removal and installation of an internal covering of a back folding door
8.2.27. Removal and installation of consolidation flew down in a back folding door
8.2.28. Replacement of an element of management of the external rear-view mirror regulated from within
8.3. Body glazing
9. Electric equipment schemes
 












8-2-10-snyatie-i-ustanovka-kapota.html

8.2.10. Removal and cowl installation

Removal
Dismantle a cowl.
At hinge replacement: dismantle a water repeller.
Uncover the block of the relay of the module of management of electronic systems of a body.

Installation
At replacement of a cover of a cowl, establish isolation.
Adjust a cowl to a wing.
Adjustment of a gap 3 is carried out in points of screwing up 1, and adjustment on height – in points of screwing up 2.
1–Points of screwing up of a cowl.
2–Points of screwing up of the hinge of a cowl.
Flatten the rivet end by means of nippers 2.
Adjust locking.
Adjusting size (X) = 40–45 mm.
To Zakontrita a round nut in the following sequence: 5 round nuts, 6 twisted spring, the 7th washer, 8 directing pin.
The moment of an inhaling of a round nut and directing pin – 22 N · m.

NOTE
Grease directing pin.

Removal and installation of a forward door

Removal
Disconnect the socket of a plait of wires.
Dismantle a door.
Unscrew the fixing screw of fastening of the tape door limiter.
Dismantle tightening plugs of the door hinge.

NOTE
To greasing of tightening plugs apply greasing of a high pressure (number of a detail 90 510 336 / number according to the catalog 19 48 606).

Installation
Establish a door.
If necessary adjust a forward door.

NOTE
Observe adjusting gaps.

Adjusting gaps

NOTE
The sizes of a gap touch the varnished lobby of a door in a set with all mounted details.

«on page back
8.2.9. Replacement of additional consolidation of a frame of a roof
on the following page»
8.2.11. Removal and installation of the lock of a forward door