Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical box передч
3.3. Automatic transmission
3.4. Driving mechanism
3.4.1. General information
3.4.2. Measurement of radial and lateral palpation of the bearing of a wheel
3.4.3. Measurement of an inclined gap of the block of the bearing
3.4.4. Removal and installation of a shaft of a wheel
3.4.5. Replacement of the internal hinge of equal angular speeds
3.4.6. Replacement of the external hinge of equal angular speeds
3.4.7. Dismantling of the external hinge of equal angular speeds
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 












3-4-4-snyatie-i-ustanovka-vala-kolesa.html

3.4.4. Removal and installation of a shaft of a wheel

Removal
Remove the corresponding forward wheel.
Disconnect a wheel shaft from a wheel nave.
Unscrew a nut from a wheel shaft.
Hold by means of the special KM-468-B tool on a forward nave of a wheel.
Remove steering draft from a rotary fist, having turned off a fastening nut.
Vypressuyte steering draft from a rotary fist, using the special KM-161-B tool together with the KM-161-2 adaptation.
Disconnect a brake hose from a supporting pipe of a spring rack.
Remove a clamping level.
Disconnect a brake hose from an arm.
Disconnect the rotary lever (1) from a supporting pipe of a spring rack.
Hold for лыски an open wrench.
Remove the hinge from a rotary fist, having unscrewed a fastening bolt.
Take away a rotary fist by means of the KM special tool 915.
Take out the hinge from a rotary fist.
Squeeze out a wheel shaft of a wheel nave.

NOTE
Thus take away a rotary fist outside, use in case of need a stripper of a nave of a wheel.

Remove the bottom cover of a motor compartment
Take out a wheel shaft from a transmission and bring down it from an intermediate shaft.

NOTE
Collect oil in the pallet and close openings caps.

Observe accuracy at the address with wheel shaft.

Installation
Establish a wheel shaft in a transmission.
Establish a new lock ring on a wheel shaft.
Cover shlitsa and points of support with oil for transmissions
Establish a wheel shaft in a transmission, hammer into a transmission a rubber hammer and to suitable soft metal small beards to a zashchelkivaniye of a lock ring.
On cars with intermediate shaft – establish a wheel shaft on an intermediate shaft.
Replace a lock ring on an intermediate shaft.
Fix the right shaft of a wheel on intermediate to a shaft.

ATTENTION
Watch to damaging a shlitsa, press an intermediate shaft, using suitable soft metal small beards to a zashchelkivaniye of a lock ring.

Establish a wheel shaft in a wheel nave.
Attach the hinge to a rotary fist and tighten the moment of 50 N · m.
Use new nuts.
Attach the rotary lever to a supporting pipe of a spring rack and tighten the moment of 55 N · m.
Use new nuts.
Hold for лыски an open wrench.
Attach steering bent for to a rotary fist and tighten the moment of 30 N · m + 90 ° +15 °.
Use new nuts.
Attach a brake hose to a supporting pipe of a spring rack.
Establish a brake hose in an arm on a supporting pipe of a spring rack.
Fix a clamping level.
Establish a wheel shaft in a nave of a wheel and tighten the moment of 150 N · m, turn on on 45 °, then and tighten the moment of 250 N · m.
Use new nuts.
Hold by means of the special KM-468-B tool for a wheel nave.
Establish a forward wheel and tighten bolts of fastening the moment of 110 N · m.
Check liquid level in transmissions.

«on page back
3.4.3. Measurement of an inclined gap of the block of the bearing
on the following page»
3.4.5. Replacement of the internal hinge of equal angular speeds