Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.5. Injection system
2.5.1. Replacement of fuel nozzles (one or all) (Z10XE, Z10XEP, without the conditioner)
2.5.2. Replacement of the fuel filter (petrol engines)
2.5.3. Removal and installation of the electric fuel pump
2.5.4. Replacement of consolidation of a final collector (Z10XE, Z10XEP, without the conditioner)
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 












2-5-4-zamena-uplotneniya-vypusknogo-kollektora-z10xe-z10xep-bez-kondicionera.html

2.5.4. Replacement of consolidation of a final collector (Z10XE, Z10XEP, without the conditioner)

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It it is necessary откалибровать anew.

Removal
Open a cowl.
Disconnect plugs of the storage battery.
Disconnect a weight wire.
Lift the car.
Dismantle an exhaust pipe in front 1.

NOTE
On option of the ECO model uncover motor office below.

Turn off 3 nuts.
Lower the car.
Dismantle soaking-up pipe 1.
Turn out a bolt 2.
Release directing tube щупа an oil meter.
Pull out щуп an oil meter.
Turn out a bolt.
Dismantle heated up a lambda sensor of regulation of structure of a fuel mix.
Disconnect the socket of a plait of wires.
Release a plait of wires.
Carefully turn out by means of the KM-61291 adaptation.
Dismantle a transport earring of the engine at the left 2.
Turn out a bolt.
Dismantle a guard of a final collector.
Turn off 2 bolts of fastening.
Dismantle a final collector.
Turn off 7 nuts of fastening.
Take out consolidation.
Clean sealing surfaces of a head of the cylinder and a final collector.
Take out directing pipe щупа an oil meter.
Installation
Insert directing tube щупа an oil meter.
Replace 2 sealing rings 1.
Establish a final collector.
Replace consolidation.
Replace nuts.
Tighten 3 nuts the moment of an inhaling of 20 N · m.
Establish a guard of a final collector.
Tighten 2 bolts of fastening with the moment of 8 N · m.
Establish a transport earring of the engine at the left.
Tighten a bolt the moment of an inhaling of 20 N · m.
Establish heated up a lambda sensor of regulation of structure of a fuel mix.
Put on a carving assembly paste (white).
Tighten a lambda sensor the moment of 40 N · m.
Connect the socket of a plait of wires.
Fix a plait of wires.
Fix directing tube щупа an oil meter.
Tighten a bolt the moment of 8 N · m.
Lift the car.
Establish an exhaust pipe in front.

NOTE
On the ECO model establish a cover of motor office below.

Replace consolidation and nuts.
Tighten 3 nuts the moment of 25 N · m.
Lower the car.
Establish soaking-up pipe.
Insert into a forward part from above.
Tighten a bolt.
Insert щуп an oil meter.
Connect plugs of the storage battery.
Program volatile memory.
Close a cowl.

«on page back
2.5.3. Removal and installation of the electric fuel pump
on the following page»
2.6. Petrol engines – the general procedures of check