Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.4. Greasing system
2.4.1. Removal and installation of the case of the oil filter (Z10XE, Z10XEP, without the conditioner)
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)
2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without the conditioner)
2.4.4. Replacement of the relay of pressure of oil (Z10XE, Z10XEP)
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293



2-4-2-zamena-motornogo-masla-z10xe-z10xep.html

2.4.2. Replacement of engine oil (Z10XE, Z10XEP)

Removal
Open a cowl.
Take out the loose leaf of the oil filter 3.
Substitute the reception pallet.
Unscrew a cover of the case of the oil filter 1.
Lift the car.

NOTE
On ECO model option: open the service valve 1 in a cover of motor office below, turn out 4 bolts of fastening.

Merge engine oil.
Turn off a carving stopper of a drain opening.

Installation
Wrap a carving stopper of a masloslivny opening.
Replace a sealing ring.
Tighten a bolt the moment of 10 N · m.
Remove the reception pallet for oil.
Lower the car.

NOTE
On ECO model option: close the service valve 1 in a cover of motor office below, wrap 4 bolts of fastening.

Establish the loose leaf of the oil filter.
Insert the loose leaf of the oil filter.
Establish a cover of the case of the oil filter.
Sealing ring 2 replace.
Cover of the case of the oil filter tighten 10 N · m.
Fill in engine oil.
Observe the ordered refueling volume of engine oil.
Start the engine and leave to work until the control lamp of pressure of oil will go out.
Check and, if necessary, modify level of engine oil.

Only for Z10XEP
Dump data of an interval of servicing.

Dumping of data of a flexible interval of servicing (ECO Service-Flex)
Indication of a flexible interval of servicing (time and kilometers) can be nulled on a combination of devices. The controler of management of the engine is connected with a combination of devices.

Manual dumping
Switch off ignition. The indicator in a speedometer should show the counter of daily run.
Press and hold the dumping button (the button of daily kilometer run).
Include ignition and wait, indication of service intervals will not be switched yet, hold pressed the dumping button not less than 3 pages.
In some seconds the indicator in a speedometer will show a symbol with the maximum run of 34 000 km for the petrol engine or 50 000 km for the diesel engine.
Time counter on the device is established for 24 months.
The controler of engine management receives a signal on the tire CAN, and the condition of oil is established for 100 %. Thereby the controler of management of the engine and the indicator are nulled.
Further it is necessary to know that the nulled service indication cannot be again staticized, especially in case there is no service magazine.
Depending on the passable piece of a way from the moment of the last replacement of motor oil/checkup new replacement of engine oil, most likely, is required to avoid engine damage.
Close a cowl.

«on page back
2.4.1. Removal and installation of the case of the oil filter (Z10XE, Z10XEP, without the conditioner)
on the following page»
2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without the conditioner)