Repair of Opel Corsa C, from 2000 to 2005 of release.
1. Operation and car maintenance
2. Engine
2.1. Petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.2. Mechanical part of petrol engines Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I
2.3. Cooling system
2.3.1. Filling of system of cooling to fill and air removal (Z10XE, Z10XEP)
2.3.2. Replacement of the sensor of temperature of cooling liquid (Z10XE, Z10XEP, without the conditioner)
2.3.3. Removal and installation of the pump of cooling liquid (Z10XE, Z10XEP, with the conditioner)
2.3.4. Removal and thermostat installation with a branch pipe of cooling liquid (Z10XE, Z10XEP, without the conditioner)
2.3.5. Radiator replacement (Z10XE, Z10XEP, with the conditioner)
2.4. Greasing system
2.5. Injection system
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Verifying and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Greasing system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Electric equipment schemes
 








99e20293 Где снять шлюху в спб.



2-3-5-zamena-radiatora-z10xe-z10xep-s-kondicionerom.html

2.3.5. Radiator replacement (Z10XE, Z10XEP, with the conditioner)

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It it is necessary откалибровать anew.

Removal
Disconnect plugs of the storage battery.
Disconnect a weight wire.
Merge cooling liquid.
Substitute the reception pallet.
Open a carving stopper of a drain opening (shooter).
Release a forward covering above.
Unscrew 3 bolts of fastening 1.
Lift the car.
Release a forward covering below.
Release 3 clips 2.
Turn off 4 bolts of fastening 1.
Turn off 2 nuts 3.
Remove a forward covering.
Disconnect the socket of a plait of wires of the sensor of temperature.
Lower the car.
Disconnect a clip from the case of the fan (shooter).
Remove, having pulled down.
Dismantle a sound signal.
Disconnect the socket of a plait of wires.
Turn out a bolt.
Lower the car.
Merge cooling liquid.
Substitute the reception pallet.
Open a carving stopper of a drain opening (shooter).
Dismantle soaking-up pipe 1.
Pull out щуп an oil meter.
Turn out a bolt 2.
Remove perepuskny a hose from a radiator.
Remove a radiator hose above.
Release 2 collars.
Dismantle a radiator hose below.
Release a collar.
Hose of a radiator disconnect from the case of the fan and the holder of the hydrounit.
Remove the fan case.
Disconnect 2 sockets of a plait of wires.
Motor of the auxiliary fan, pneumatic switch.
Turn off 2 bolts of fastening 1.
The case of the fan carefully to pull up and to put on the engine.
Release the refrigerating condenser.

NOTE
Central air of air remains closed.

Turn off 2 bolts of fastening (shooters).
The condenser Take out from the holder.
To suspend the condenser.
Dismantle a radiator.
Dismantle 2 holders of a radiator below.
Turn off 4 bolts of fastening.
Radiator carefully pull out, having pulled down.
Installation
Establish a radiator.
Close a carving stopper of a drain opening of cooling liquid.
Insert a radiator.
Establish 2 holders of a radiator below.
Tighten 4 bolts of fastening the moment of 25 N · m.
Fix the refrigerating condenser.
To unhook the condenser.
Insert in the holder.
Tighten 2 bolts of fastening the moment of 5 N · m.
Establish the fan case.
The fan case carefully get.
Tighten 2 bolts of fastening the moment of 5 N · m.
Connect the socket of a plait of wires.
Radiator hose below establish.
Fix a collar.
Fix a hose.
Radiator hose above establish.
Fix 2 collars.
Establish perepuskny a hose.
Establish soaking-up pipe.
Insert into a forward part from above.
Tighten a bolt.
Insert щуп an oil meter.
Lift the car.
Establish a sound signal.
Tighten a bolt.
Connect the socket of a plait of wires.
Establish a fixing clip.
Establish a forward covering.
Connect the socket of a plait of wires.
Fix a forward covering below.
Establish 3 clips.
Twirl 4 bolts of fastening.
Twirl 2 nuts.
Lower the car
Fix a forward covering from above.
Tighten 3 bolts of fastening.
Connect plugs of the storage battery.
To fill system of cooling and remove from it air.
Program volatile memory.
Close a cowl.

«on page back
2.3.4. Removal and thermostat installation with a branch pipe of cooling liquid (Z10XE, Z10XEP, without the conditioner)
on the following page»
2.4. Greasing system